Terminal1010x by Rane

The Terminal 1010x takes the DSP Experience to the next level with an intuitive front-panel that enables users to control 10 analog balanced inputs for Mic/Line/+48V and 10 balanced outputs. There are also 6 flexible RAD Plus PoE ports to connect breakout boxes and wall plate remote controls and 4 Universal GPIO logic ports for external devices such as alarm systems, sensors, lights, projectors, etc. There is also a slot for an optional DANTE 32x32 card for network connectivity.

Features:

• Native Analog 10-in/10-out
• 6 RAD+ Ports support RADs and DRs - adds 12-in/12-out, for a total 22-in/22-out
• Optional DANTE card adds 32-in/32-out on the network
• Expansion Port for future hardware releases
• Online Wizard for quick-start using Halogen software
• Enhanced front panel control and monitoring

Package Contents:

• Terminal 1010x
• (5) 6-pin 3.8 mm Euroblock input (green, for audio inputs)
• (5) 6-pin 3.8 mm Euroblock outputs (orange, for zone outputs)
• (1) 6-pin 3.8 mm Euroblock input (black, for logic input)
• IEC Power Cable
• Quickstart Guide
• Safety & Warranty Manual

Specifications:

Analog I/O:
Type: 10 in x 10 out
ADC: High definition audio 24-bit, 48kHz, DR 116dB A-weighted
DAC: High definition audio 24-bit, 48kHz, DR 116dB A-weighted
Frequency Response: 20Hz–20kHz, ±0.1dB

Inputs:    
Connection: (5) Euroblock connectors, 6 pins each, 3.81mm pitch, green. Ships with strain relief plugs.

Condenser Mic Mode:
Type: Active balanced, microphone input mode with 48V phantom power
Phantom Power: +48V
Maximum Input: 1Vrms
Input Impedance: 2.5kΩ: Each leg

Dynamic Mic Mode:
Type: Active balanced, microphone input mode without phantom power
Maximum Input: 250mVrms
Input Impedance: 2.5kΩ: Each leg

Line Mode:
Type: Active balanced, line-level
Maximum Input: 8Vrms
Input Impedance: 5kΩ: Each leg

Line+ Mode:
Type: Active, left [+] & right [-] signals summed to mono
Maximum Input: 8Vrms
Input Impedance: 5kΩ: Each leg

Outputs:
Connection: (5) Euroblock connectors, 6 pins each, 3.81mm pitch, orange. Ships with strain relief plugs.
Type: Active balanced, line output mode with active output transient muting
Maximum Output: 8Vrms
Impedance: 300Ω: Each leg
Frequency Response: 20Hz–20kHz, ±0.1dB

DSP:
Processing Power: >10,000 MIPS
Word Length: 32-/64-bit Floating Point
Delay Memory: Min. 160sec total

Computer Interface:
Type: Ethernet 1000 base-T: Zeroconf service discovery protocol for easy setup
Connection: RJ-45: Shielded Cat 5e cable or better
Length: 300ft./100m: Standard Ethernet cable length limit

RAD+ Ports:
Connection: (6) RJ-45: Shielded Cat 5e cable or better
Audio Channels: 2 in, 2 out: Each port, control channel 24-bit, 48kHz
Voltage: 27 VDC: Each port
Power: 12W (peak)/6W (average): Each port
Length: DR devices: 984ft./300m: RAD devices: 325ft./100m

Universal Logic I/O:
Connection: (1) mini-Euroblock connector, 6 pins, 3.81mm pitch, black

Logic In:
Internal Pull-Up: 5mA: Protected to +24V, reverse-polarity-protected
Vin High: > 2.2V: Normal state
Vin Low: < 1.0V

Logic Out:
Open Collector Output: Source 5mA, Sink 200mA Protected to +24V, reverse-polarity-protected
Vout High: > 2.2V
Vout Low: < 0.2V

Ratiometric Input:
Input: 0–5V
V+: 40mA
Resolution: 8-bit at 2kHz sample rate

Expansion Port:
Types:
Rane Expansion Bus: 512 x 512, 48kHz digital audio plus control. Up to 32 Halogen Expansion Devices
Dante card (optional): 32 x 32 with sample-rate conversion, allowing 96kHz sample rate Dante flows
Connection: RJ-45: Shielded Cat 5e cable or better
Maximum Length: 300ft./100m

Power:
Connection: IEC
Voltage: 90–260VAC, 50/60Hz
Consumption: 70W
Output: 28V

Unit:
Wiring: Class 2: Rear-panel terminals
Operating Temperature: 32–104°F, 0–40°C
Fan: 10CFM, low noise (<20dBa), long life (60k hours at 45°C)
Dimensions: 19.0" x 8.25" x 1.73"
48.3cm x 20.9cm x 4.4cm: Width x depth x height
Weight: 7.0 lbs., 3.2 kg